Tången 2 is a building situated in Stockholm, Sweden. It´s built in the 1930s and contains both residences and businesses. The property owner, Diligentia AB, wants to lower the energy use in Tången 2. This report consists of an energy audit which clarifies the specific circumstances linked to Tången 2. Collected knowledge is then used, together with the results from the literature study, to decide energy measures to proceed with.

Former studies have shown that a considerable part of industries? energy usage can stem from idle times in the production. This thesis, carried out at Siemens Industry sector, evaluates the potential for using the control system to automatically put machines into energy saving mode during idle times. The main part of the thesis consists of a case study performed on machine tools at a Scania production site in Södertälje. Through load measurements the potential for energy savings was determined.The results show that there is a great potential for energy savings during idle times at the site.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

The purpose of the study was to investigate the use and losses of energy in an existing older building. Another purpose was also to look through various options for heating systems with renewable energy in the building. The aim was to reduce the use and losses of energy. The first step was to study the related electricity bills of the building and also perform measurements and calculations of the building envelope and ventilation. The next step was to find out the possible actions for energy saving by performing measurements and calculations.

This study has been carried out in the spring of 2014 on behalf of PQR Consult AB in Stockholm. The aim of the study has been to analyse the energy usage of the building Skarpövägen 1 in order to explore the possibilites of saving energy by using appropriate equipment. These possible solutions have been simulated by using the programe IDA Indoor Climate and Energy, combined with a life cycle cost analysis. The laundry building, Skarövägen 23, has also been analysed due to its high amount of energy usage. The result of the energy analysis showed that the energy usage was much higher than the energy declaration.

Volvo Trucks is the second largest manufacturer of heavy trucks, with factories in several countries and with around 21 000 employees. At the plant in Tuve, trucks have been built since 1982 and the activity mainly consists of producing side members and to assemble and packing kits of trucks. In 2005, the factory in Tuve launched the ambition to be the first carbon dioxide neutral vehicle factory in the world. This will be implemented by streamlining and investing in renewable energy. The aim of this degree thesis is to map the usage of energy within production, and also to prepare a method to measure key figures (use of energy per produced unit).

In Sweden, a big part of the energy use is used in the housing sector. Political goals and targets are set up which the housing sector needs to work towards. Apartment buildings are a major part of the housing sector in Sweden and therefore reduction of energy use in these kinds of buildings are key to lower the energy use in Sweden. But there are not only political incentives to reduce the energy use. Some energy?saving measures are directly profitable and should thus be performed.

In Uppsala, Sweden, Vattenfall has a combined heat and power plant. On the premises there is an engineering workshop with old fluorescent and mercury lamps that need to be replaced. This provides a great opportunity to save energy and money by installing more efficient lighting. The main purpose of this study was to present two functional and energy efficient lighting systems including control system. The lighting systems were designed by investigating the working environment, measuring illuminance and by simulations in the software DIALux.

The purpose of the study was to investigate the use and losses of energy in an existing older building. Another purpose was also to look through various options for heating systems with renewable energy in the building. The aim was to reduce the use and losses of energy. The first step was to study the related electricity bills of the building and also perform measurements and calculations of the building envelope and ventilation. The next step was to find out the possible actions for energy saving by performing measurements and calculations.

Increased energy consumption in the world has created an increased supply of various fuels, especially fossil fuels. The Swedish government has set up various energy targets for 2020. To reach these goals it?s important to increase the energy efficiency in local buildings such as schools. This work illustrates the breakdown between energy supply and energy losses over the school.

The present climate discussion has made energy efficiency an interesting topic. Saving energy does not only help the climate but also saves money for the energy consumer. The purpose of this thesis was to examine the potential of heat recovering from milk cooling. Two milk farms, one with voluntary milking system, VMS, and the other with conventional milking system was used to measure interesting temperatures and electricity consumptions. The numbers were used both to do theoretical calculations and to construct a SIMULINK model. To calculate the potential for heat at milk farms theoretical calculations were made in MATLAB using a reference farm with different combinations of heat recovery and pre cooling. The farm was assumed to keep a dwelling house with the annual heat consumption 18165 kWh.

Abstrakt -  As energy prices rise, energy-saving in buildings is becoming increasingly important. By applying different construction and installation technologies, to new buildings the energy consumption can be reduced effectively, compared to similar existing buildings. These technical measures are often an investment in the long term and will reduce energy costs significantly. The purpose of this report is to show how to reduce energy consumption in a small house. It is presented in this report that both building's technical saving arrangements (the sealing of a building) and an installation technical arrangement (changing from the F-system to the FTX-system) would reduce energy consumption in newly built detached houses, if compared with a similar existing house but without these technical measures. The report presents also detailed calculations showing how much energy an existing 2-storey house, built in the year 2007 in Eskilstuna, consumes and how much energy would be saved if these corrective measures were applied to a new building. It is also reported how much money would be saved each year over a 10 year period if the measures were applied. The results show that both solutions are a good investment in the reduction of energy consumption and hence the cost involved. Keywords: energy, heat energy, infiltration, FTX-system, free temperature effectively. .

The number of people in the world and the urbanization increases. This leads to a bigger need of space for the built environment, space that soon doesn?t exist. A large portion of humanity?s energy disposal is used for heating of buildings.